Our Top 10 Recommendations for Car Audio Amplifiers

Up-to-date pricing and reviews for car audio amplifiers on the market

Bestseller No. 1

POWER: Maximum Power Output of 1100 Watts at 2 Ohms into one channel. MAX power output of 550 Watts at 4 Ohms into one Channel. This amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to
HIGH LEVEL INPUTS: Speaker level inputs are commonly referred to as high-level inputs. Speaker level inputs will be used to connect the R1100M to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
LOW LEVEL INPUTS: Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the R1100M with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
LOW-PASS CROSSOVER: A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
VARIABLE BASS BOOST: Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it

Bestseller No. 2

Bestseller No. 3

Power - 100 Watts Max x 4 @2-Ohms, 50 Watts Max x 4 @4-Ohms
Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
Full Range - With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers
Variable Gain Control - The gain control is not for adjusting volume. It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier
Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers

Bestseller No. 4

1500W Maximum Power Full-Range Amplifier
Optimized 150-watt RMS output and a max power output of 1500 watts, you can give your music a huge boost in power that will have you and your passengers partying while on the road
This slim amplifier fits perfectly into any trunk so you can easily connect it to your stereo system

Bestseller No. 5

300 Watts x 1 @ 4-Ohms, 500 Watts x 1 @ 2-Ohms, Frequency 20Hz to 250Hz +/-1dB
Onboard 12dB/octave LP/HP/AP crossover & Infrasonic filter. Power Wire Gauge- 4 AWG. Power Input Connector-Screw Terminal. Suggested Alternator-75 A
On-board Punch EQ with +18dB boost at 45Hz. Input Sensitivity: 150 mV to 4 V
Cast Aluminum Heatsink with Stealth top mounted control panel
Includes wired remote (Punch Level Control). High efficiency amplifier design that reduces current consumption from the charging system

SaleBestseller No. 6

Power - 1500 Watts Max x 1 @2-Ohms, 750 Watts Max x 1 @4-Ohms
Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers
Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it

Bestseller No. 7

Bestseller No. 8

Mono Block Class D 4000 Watts (Peak Power) Amplifier
RMS Power Handling @ 1 Ohm: 750 Watts x 1/ RMS Power Handling @ 2 Ohms: 530 Watts x 1/ RMS Power Handling @ 4 Ohms: 300 Watts x 1
Total Harmonic Distortion (THD): < 1%/ Frequency Response 1dB: 10Hz?300KHz/ Signal To Noise Ratio: > 85dB
Low Level Input Sensitivity: 0.2-6V/ Dimensions LxHxW: 13.66 Inches x 2.05 Inches x 8.94 Inches

Bestseller No. 9

Class D MOSFET Monoblock Power Amplifier
Peak Power at 1 Ohm: 2,800 Watts | RMS Power at 1 Ohm: 2,000 Watts
Frequency Response: 20Hz - 250Hz, On-board Bass EQ Switch with +6 or +12dB boost at 45Hz
Featuring 4-Way Protection Circuitry and 1/0 AWG Power & Ground Input Terminals for Maximum Current Flow
Stable at 1 ohm | Remote Subwoofer Level Control Included

Bestseller No. 10

POWER: Max Power Output of 1500 Watts at 2 Ohms into one channel. Maximum Power output of 750 Watts at 4 Ohms into one Channel. This amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to
HIGH LEVEL INPUTS: Speaker level inputs are commonly referred to as high-level inputs. This input will be used to connect the AC1500.1M to your factory radio or aftermarket radio that does not have low-level (RCA) inputs
LOW LEVEL INPUTS: Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the AC1500.1M with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
LOW-PASS CROSSOVER: A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. A low-pass filter will primarily keep high notes out of your subwoofer(s)
VARIABLE BASS BOOST: Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it